Canadian Electric Vehicles
Tel: (250) 954-2230
Fax: (250) 954-2235
Email: sales@canev.com
/ Might-E Truck / Might-E Tug / Might-E Cart / Airport Service Vehicles / Industrial Vehicles /

Adapters $825.00 US

Canadian Electric Vehicles manufactured stock adapters are in stock and ready for next day shipping.
All Adapters include Hub and Hardware.


Chevy
4 Cylinder:
2.2L 2.5L 2.8L
L Series (Vortec)
V6 & V8

Dodge
4 Cylinder:
1.8L, 2.0L, 2.4L

Ford
4 Cylinder:
2.3L ,2.5L
Duratec
V6 / V8:
3L
2.8L, 2.9L, 4L
V8

Honda
4 Cylinder:
B Series Engine
D Series Engine

Jeep
4 Cylinder
6 Cylinder

Mazda
RX7 / RX8
L Series Engine
B Series Engine

Nissan
4 Cylinder:
L & Z Series Engine

Porsche
Air Cooled

Saturn
4 Cylinder

Suzuki / Geo
4 Cylinder:
1.0L, 1.3L, 1.6L, 2.0L
600CC

Toyota
4 Cylinder:
R Series Engine
S Series Engine
N Series Engine
Z Series Engine

VW
Air Cooled
Liquid Cooled

  Adapter

 





All adapters retain use of original clutch and fit most ADC, WARP and HPEV AC31/AC50 Motors.
If you would like a detailed estimate with the cost of the parts we have for your conversion, please e-mail us with your vehicle specifications:
Year, Make/Model, Size of Engine, Manual/Automatic/Power Steering/Air Conditioning and the country you reside in.

Some adapter plates may have more or less bolt holes than your make and model of vehicle requires. As some adapters span a broad range of model years the adapter is designed to have enough bolt holes to be compatible with all model designs. Auto manufacturers are making changes to the transmissions all the time so the outer profile and starter hole location may not be a perfect match.
The PDF drawings on each adapter page are a good reference to compare your transmission to. Please use the PDF to confirm both adapter hole layout and hub flywheel bolt pattern.

Taper lock Verses set screw hubs info:
Over the years there have been two ways of holding the adapter hub to the motor shaft and it causes great debates. The taper lock hub uses three or more bolts to pull the hub onto a tapered locking sleeve. This works well if the bolts are done up gradually and evenly and the sleeve does not move on the shaft while your pulling the two parts together. The biggest problem is pulling them on straight. If they are pulled a bit crooked then you end up with a flywheel wobble and vibration. There is also a chance that while pulling the two parts together the inner sleeve will move on the shaft which moves the position of the flywheel and the clutch will not work properly. CEV has used the taper lock hub on its S-10 and air cooled VW adapters for a long time but due to occasional wobble problems we switch to set screw hubs on all adapters with no more problems. Our set screw hubs slide all the way onto the shaft and bottom on the motor front bearing. This eliminates any chance that the hub could move in the future. All the clutch force is transmitted directly to the bearing rather than through the set screw. Some The setscrew hubs (not ours) were installed on the motor shaft to the correct distance from the adapter face ( the magic number). Then a small hole drilled in the motor shaft and a set screw done up to keep it in the right place. Over time this could wear and the set screw could come loose from repeated use of the clutch.

Reasons why we built clutch-type adapters:
1. Safety disconnect. If the motor were to lock up you can disconnect it from the rear axle and avoid locking up the rear wheels.
2. If the controller were to fail full ON (and they do) you can disconnect the motor so your not rocketing through a stop sign.
3. Have your tried to shift without a clutch? Yes you can get on to it but we like to build vehicles that anyone can jump into a drive without having to learn the "tricks" of shifting without the clutch.
4. We have built vehicles with both systems and find no noticeable difference that the extra flywheel weight makes. Yes there is a theoretical difference but I have never been able to tell by driving both systems in the same vehicle.
5. Most clutchless adapters are the same cost as our clutch adapters so no savings on cost.
6.There is no modification to the clutch to work with our adapters. We make the drive end of the motor "look" like the back end of the gas engine so the flywheel bolts on just like stock.